Videos/A Digital Media Primer For Geeks
Wiki edition
- Watch
- Download
- Up to videos page
Introduction
Workstations and high end personal computers have been able to manipulate digital audio pretty easily for about fifteen years now. It's only been about five years that a decent workstation's been able to handle raw video without a lot of expensive special purpose hardware.
But today even most cheap home PCs have the processor power and storage necessary to really toss raw video around, at least without too much of a struggle. So now that everyone has all of this cheap media-capable hardware, more people, not surprisingly, want to do interesting things with digital media, especially streaming. YouTube was the first huge success, and now everybody wants in.
Well good! Because this stuff is a lot of fun!
It's no problem finding consumers for digital media. But here, I'd like to address the engineers, the mathematicians, the hackers, the people who are interested in discovering and making things and building the technology itself. The people after my own heart.
Digital media, compression especially, is perceived to be super-elite, somehow incredibly more difficult than anything else in computer science. The big industry players in the field don't mind this perception at all; it helps justify the staggering number of very basic patents they hold. They like the image that their media researchers "are the best of the best, so much smarter than anyone else that their brilliant ideas can't even be understood by mere mortals. This is bunk.
Digital audio and video and streaming and compression offer endless deep and stimulating mental challenges, just like any other discipline. It seems elite because so few people have been been involved. So few people have been involved perhaps because so few people could afford the expensive, special-purpose equipment it required. But today, just about anyone watching this video has a cheap, general-purpose computer powerful enough to play with the big boys. There are battles going on today around HTML5 and browsers and video and open vs. closed. So now is a pretty good time to get involved. The easiest place to start is probably understanding the technology we have right now.
This is an introduction. Since it's an introduction, it glosses over a ton of details so that the big picture's a little easier to see. Quite a few people watching are going to be way past anything that I'm talking about, at least for now. On the other hand, I'm probably going to go too fast for folks who really are are brand new to all of this, so if this is all new, relax. The important thing is to pick out any ideas that really grab your imagination. Especially pay attention to the terminology surrounding those ideas, because with those, and Google, and Wikipedia, you can dig as deep as interests you.
So, without any further ado, welcome to one hell of a new hobby.
Analog vs Digital
Sound is the propagation of pressure waves through air, spreading out from a source like ripples spread from a stone tossed into a pond. A microphone, or the human ear for that matter, transforms these passing ripples of pressure into an electric signal. Right, this is middle school science class, everyone remembers this. Moving on.
That audio signal is a one-dimensional function, a single value varying over time. If we slow the 'scope down a bit... that should be a little easier to see. A few other aspects of the signal are important. It's continuous in both value and time; that is, at any given time it can have any real value, and there's a smoothly varying value at every point in in time. No matter how much we zoom in, there are no discontinuities, no singularities, no instantaneous steps or points where the signal ceases to exist. It's defined everywhere. Classic continuous math works very well on these signals.
A digital signal on the other hand is discrete in both value and time. In the simplest and most common system, called Pulse Code Modulation, one of a fixed number of possible values directly represents the instantaneous signal amplitude at points in time spaced a fixed distance apart. The end result is a stream of digits.
Now this looks an awful lot like this. It seems intuitive that we should somehow be able to rigorously transform one into the other, and good news, the Sampling Theorem says we can and tells us how. Published in its most recognizable form by Claude Shannon in 1949 and built on the work of Nyquist, and Hartley, and tons of others, the sampling theorem states that not only can we go back and forth between analog and digital, but also lays down a set of conditions for which conversion is lossless and the two representations become equivalent and interchangable. When the lossless conditions aren't met, the sampling theorem tells us how and how much information is lost or corrupted.
Up until very recently, analog technology was the basis for practically everything done with audio, and that's not because most audio comes from an originally analog source. You may also think that since computers are farily recent, analog signal technology must have come first. Nope. Digital is actually older. The telegraph predates the telephone by half a century and was already fully mechanically automated by the 1860s, sending coded, multiplexed digital signals long distances. You know... Tickertape. Harry Nyquist of Bell Labs was researching telegraph pulse transmission when he published his description of what later became known as the Nyquist frequency, the core concept of the sampling theorem. Now, it's true the telegraph was transmitting symbolic information, text, not a digitized analog signal, but with the advent of the telephone and radio, analog and digital signal techology progressed rapidly and side-by-side.
Audio had always been manipulated as an analog signal because... well, gee it's so much easier. A second-order lowpass filter, for example, requires two passive components. An all-analog short-time Fourier transform, a few hundred. Well, maybe a thousand if you want to build something really fancy [bang on the 3585]. Processing signals digitally requires millions to billions of transistors running at microwave frequencies, support hardware at very least to digitize and reconstruct the analog signals, a complete software ecosystem for programming and controlling that billion-transistor juggernaut, digital storage just in case you want to keep any of those bits for later...
So we come to the conclusion that analog is the only practical way to do much with audio... well, unless you happen to have a billion transistors and all the other things just lying around. And since we do, digital signal processing becomes very attractive.
For one thing, analog componentry just doesn't have the flexibility of a general purpose computer. Adding a new function to this beast... yeah, it's probably not going to happen. On a digital processor though, just write a new program. Software isn't trivial, but it is alot easier.
Perhaps more importantly though every analog component is an approximation. There's no such thing as a perfect transistor, or a perfect inductor, or a perfect capacitor. In analog, every component adds noise and distortion, usually not very much, but it adds up. Just transmitting an analog signal, especially over long distances, progressively, measurably, irretrievably corrupts it. Besides, all of those single-purpose analog components take up alot of space. Two lines of code on the billion transistors back here can implement a filter that would require an inductor the size of a refrigerator.
Digital systems don't have these drawbacks. Digital signals can be stored, copied, manipulated and transmitted without adding any noise or distortion. We do use lossy algorithms from time to time, but the only unavoidably non-ideal steps are digitization and reconstruction, where digital has to interface with all of that messy analog. Messy or not, modern conversion stages are very, very good. By the standards of our ears, we can consider them practically losless as well.
With a little extra hardware, then, most of which is now small and inexpensive due to our modern industrial infrastructure, digital audio is the clear winner over analog. So let us then go about storing it, copying it, manipulating it, and transmitting it.
Raw (digital audio) meat
Pulse Code Modulation is the most common representation for raw audio. Other practical representations do exist, for example the Sigma-Delta coding used by the SACD, which is a form of Pulse Density Modulation. That said, Pulse Code Modulation is far and away dominant, mainly because it's so mathematically convenient. An audio engineer can spend an entire career without running into anything else.
PCM encoding can be characterized in three parameters, making it easy to account for every possible PCM variant with mercifully little hassle.
sample rate
The first parameter is the sampling rate. The highest frequency an encoding can represent is called the Nyquist Frequency. The Nyquist frequency of PCM happens to be exactly half the sampling rate. Therefore the sampling rate directly determines the highest possible frequency in the digitized signal.
Analog telephone systems traditionally band-limited voice channels to just under 4kHz, so digital telephony and most classic voice applications use an 8kHz sampling rate, the minimum sampling rate necessary to capture the entire bandwidth of a 4kHz channel. This is what an 8kHz sampling rate sounds like--- a bit muffled but perfectly intelligible for voice. This is the lowest sampling rate that's ever been used widely in practice.
From there, as power, and memory, and storage increased, consumer computer hardware went to offering 11, and then 16, and then 22, and then 32kHz sampling. With each increase in the sampling rate and the Nyquist frequency, it's obvious that the high end becomes a little clearer and the sound more natural.
The Compact Disc uses a 44.1kHz sampling rate, which is again slightly better than 32kHz, but the gains are becoming less distinct. 44.1kHz is a bit of an oddball choice, especially given that it hadn't been used for anything prior to the compact disc, but the huge success of the CD has made it a common rate.
The most common hi-fidelity sampling rate aside from the CD is 48kHz. There's vitually no audible difference between the two. This video, or at least the original version of it, was shot and produced with 48kHz audio, which happens to be the original standard for high-fidelity audio with video.
Super-hi-fidelity sampling rates of 88, and 96, and 192kHz have also appeared. The reason for the sampling rates beyond 48kHz isn't to extend the audible high frequencies further. It's for a different reason.
Stepping back for just a second, the French mathematician Jean Baptiste Joseph Fourier showed that we can also think of signals like audio as a set of component frequencies. This frequency domain representation is equivalent to the time representation; the signal is exactly the same, we're just looking at it a different way. Here we see the frequency domain representation of a hypothetical analog signal we intend to digitally sample.
The sampling theorem tells us two essential things about the sampling process. First, that a digital signal can't represent any frequencies above the Nyquist frequency. Second, and this is the new part, if we don't remove those frequencies with a lowpass filter before sampling, the sampling process will fold them down into the representable frequency range as aliasing distortion.
Aliasing, in a nutshell, sounds freakin' awful, so it's essential to remove any beyond-Nyquist frequencies before sampling and after reconstruction.
Human frequency perception is considered to extend to about 20kHz. In 44.1 or 48kHz sampling, the lowpass before the sampling stage has to be extremely sharp to avoid cutting any audible frequencies below 20kHz but still not allow frequencies above the Nyquist to leak forward into the sampling process. This is a difficult filter to build and no practical filter succeeds completely. If the sampling rate is 96kHz or 192kHz on the other hand, the lowpass has an extra octave or two for its transition band. This is a much easier filter to build. Sampling rates beyond 48kHz are actually one of those messy analog stage compromises.
sample format
The second fundamental PCM parameter is the sample format, that is, the format of each digital number. A number is a number, but a number can be represented in bits a number of different ways.
Early PCM was eight bit linear, encoded as an unsigned byte. The dynamic range is limited to about 50dB and the quantization noise, as you can hear, is pretty severe. Eight bit audio is vanishingly rare today.
Digital telephony typically uses one of two related non-linear eight bit encodings called A-law and mu-law. These formats encode a roughly 14 bit dynamic range into eight bits by spacing the higher amplitude values farther apart. A-law and mu-law obviously improve quantization noise compared to linear 8-bit, and voice harmonics especially hide the remaining quantization noise well. All three eight bit encodings, linear, A-law, and mu-law, are typically paired with an 8kHz sampling rate, though I'm demonstrating them here at 48kHz.
Most modern PCM uses 16 or 24 bit two's-complement signed integers to encode the range from negative infinity to zero decibels in 16 or 24 bits of precision. The maximum absolute value corresponds to zero decibels. As with all the sample formats so far, signals beyond zero decibels and thus beyond the maximum representable range are clipped.
In mixing and mastering, it's not unusual to use floating point numbers for PCM instead of integers. A 32 bit IEEE754 float, that's the normal kind of floating point you see on current computers, has 24 bits of resolution, but a seven bit floating point exponent increases the representable range. Floating point usually represents zero decibels as +/-1.0, and because floats can obviously represent considerably beyond that, temporarily exceeding zero decibels during the mixing process doesn't cause clipping. Floating point PCM takes up more space, so it tends to be used only as an intermediate production format.
Lastly, most general purpose computers still read and write data in octet bytes, so it's important to remember that samples bigger than eight bits can be in big or little endian order, and both endiannesses are common. For example, Microsoft WAV files are little endian, and Apple AIFC files tend to be big-endian. Be aware of it.
channels
The third PCM parameter is the number of channels. The convention in raw PCM is to encode mutiple channels by interleaving the samples of each channel together into a single stream. Straightforward and extensible.
done!
And that's it! That describes every PCM representation ever. Done. Digital audio is _so easy_! There's more to do of course, but at this point we've got a nice useful chunk of audio data, so let's get some video too.
Video vegetables (they're good for you!)
One could think of video as being like audio but with two additional spatial dimensions, X and Y, in addition to the dimension of time. This is mathematically sound. The Sampling Theorem applies to all three video dimensions just as it does the single time dimension of audio.
Audio and video are obviously quite different in practice. For one, compared to audio, video is huge. Raw CD audio is about 1.4 megabits per second. Raw 1080i HD video is over 700 megabits per second. That's more than 500 times more data to capture, process and store per second. By Moore's law... that's... let's see... roughly eight doublings times two years, so yeah, computers requiring about an extra fifteen years to handle raw video after getting raw audio down pat was about right.
Basic raw video is also just more complex than basic raw audio. The sheer volume of data currently necessitates a representation more efficient than the linear PCM used for audio. In addition, electronic video comes almost entirely from broadcast television alone, and the standards committees that govern broadcast video have always been very concerned with backward compatibility. Up until just last year in the US, a sixty year old black and white television could still show a normal analog television broadcast. That's actually a really neat trick.
The downside to backward compatibility is that once a detail makes it into a standard, you can't ever really throw it out again. Electronic video has never started over from scratch the way audio has multiple times. Sixty years worth of clever but obsolete hacks necessitated by the passing technology of a given era have built up into quite a pile, and because digital standards also come from broadcast television, all these eldritch hacks have been brought forward into the digital standards as well.
In short, there are a whole lot more details involved in digital video than there were with audio. There's no hope of covering them all completely here, so we'll cover the broad fundamentals.
resolution and aspect
The most obvious raw video parameters are the width and height of the picture in pixels. As simple as that may sound, the pixel dimensions alone don't actually specify the absolute width and height of the picture, as most broadcast-derived video doesn't use square pixels. The number of scanlines in a broadcast image was fixed, but the effective number of horizontal pixels was a function of channel bandwidth. Effective horizontal resolution could result in pixels that were either narrower or wider than the spacing between scanlines.
Standards have generally specified that digitally sampled video should reflect the real resolution of the original analog source, so a large amount of digital video also uses non-square pixels. For example, a normal 4:3 aspect NTSC DVD is typically encoded with a display resolution of 704 by 480, a ratio wider than 4:3. In this case, the pixels themselves are assigned an aspect ratio of 10:11, making them taller than they are wide and narrowing the image horizontally to the correct aspect. Such an image has to be resampled to show properly on a digital display with square pixels.
frame rate and interlacing
The second obvious video parameter is the frame rate, the number of full frames per second. Several standard frame rates are in active use. Digital video, in one form or another, can use all of them. Or, any other frame rate. Or even variable rates where the frame rate changes adaptively over the course of the video. The higher the frame rate, the smoother the motion and that brings us, unfortunately, to interlacing.
In the very earliest days of broadcast video, engineers sought the fastest practical framerate to smooth motion and to minimize flicker on phosphor-based CRTs. They were also under pressure to use the least possible bandwidth for the highest resolution and fastest frame rate. Their solution was to interlace the video where the even lines are sent in one pass and the odd lines in the next. Each pass is called a field and two fields sort of produce one complete frame. "Sort of", because the even and odd fields aren't actually from the same source frame. In a 60 field per second picture, the source frame rate is actually 60 full frames per second, and half of each frame, every other line, is simply discarded. This is why we can't deinterlace a video simply by combining two fields into one frame; they're not actually from one frame to begin with.
gamma
The cathode ray tube was the only available display technology for most of the history of electronic video. A CRT's output brightness is nonlinear, approximately equal to the input controlling voltage raised to the 2.5th power. This exponent, 2.5, is designated gamma, and so it's often referred to as the gamma of a display. Cameras, though, are linear, and if you feed a CRT a linear input signal, it looks a bit like this.
As there were originally to be very few cameras, which were fantastically expensive anyway, and hopefully many, many television sets which best be as inexpensive as possible, engineers decided to add the necessary gamma correction circuitry to the cameras rather than the sets. Video transmitted over the airwaves would thus have a nonlinear intensity using the inverse of the set's gamma exponent, so that once a camera's signal was finally displayed on the CRT, the overall response of the system from camera to set was back to linear again.
Almost.
There were also two other tweaks. A television camera actually uses a gamma exponent that's the inverse of 2.2, not 2.5. That's just a correction for viewing in a dim environment. Also, the exponential curve transitions to a linear ramp near black. That's just an old hack for suppressing sensor noise in the camera.
Gamma correction also had a lucky benefit. It just so happens that the human eye has a perceptual gamma of about 3. This is relatively close to the CRT's gamma of 2.5. An image using gamma correction devotes more resolution to lower intensities, where the eye happens to have its finest intensity discrimination, and therefore uses the available scale resolution more efficiently. Although CRTs are currently vanishing, a standard sRGB computer display still uses a nonlinear intensity curve similar to television, with a linear ramp near black, followed by an exponential curve with a gamma exponent of 2.4. This encodes a sixteen bit linear range down into eight bits.
color and colorspace
The human eye has three apparent color channels, red, green, and blue, and most displays use these three colors as additive primaries to produce a full range of color output. The primary pigments in printing are Cyan, Magenta, and Yellow for the same reason; pigments are subtractive, and each of these pigments subtracts one pure color from reflected light. Cyan subtracts red, magenta subtracts green, and yellow subtracts blue.
Video can be and sometimes is represented with red, green, and blue color channels, but RGB video is atypical. The human eye is far more sensitive to luminosity than it is the color, and RGB tends to spread the energy of an image across all three color channels. That is, the red plane looks like a red version of the original picture, the green plane looks like a green version of the original picture, and the blue plane looks like a blue version of the original picture. Black and white times three. Not efficient.
For those reasons and because, oh hey, television just happened to start out as black and white anyway, video usually is represented as a high resolution luma channel, the black & white, along with additional, often lower resolution chroma channels, the color. The luma channel, Y, is produced by weighting and then adding the separate red, green and blue signals. The chroma channels U and V are then produced by subtracting the luma signal from blue and the luma signal from red.
When YUV is scaled, offset and quantized for digital video, it's usually more correctly called Y'CbCr, but the more generic term YUV is widely used to decribe all the analog and digital variants of this color model.
chroma subsampling
The U and V chroma channels can have the same resolution as the Y channel, but because the human eye has far less spatial color resolution than spatial luminosity resolution, chroma resolution is usually halved or even quartered in the horizontal direction, the vertical direction, or both, usually without any significant impact on the apparent raw image quality. Practically every possible subsampling variant has been used at one time or another, but the common choices today are 4:4:4 video, which isn't actually subsampled at all, 4:2:2 video in which the horizontal resolution of the U and V channels is halved, and most common of all, 4:2:0 video in which both the horizonal and vertical resolutions of the chroma channels are halved, resulting in U and V planes that are each one quarter the size of Y.
The terms 4:2:2, 4:2:0, 4:1:1 and so on and so forth, aren't complete descriptions of a chroma subsampling. There's multiple possible ways to position the chroma pixels relative to luma, and again, several variants are in active use for each subsampling. For example, motion JPEG, MPEG-1 video, MPEG-2 video, DV, Theora and WebM all use or can use 4:2:0 subsampling, but they site the chroma pixels three different ways.
Motion JPEG, MPEG1 video, Theora and WebM all site chroma pixels between luma pixels both horizontally and vertically.
MPEG2 sites chroma pixels between lines, but horizontally aligned with every other luma pixel. Interlaced modes complicate things somewhat, resulting in a siting arrangement that's a tad bizaare.
And finally PAL-DV, which is always interlaced, places the chroma pixels in the same position as every other luma pixel in the horizonatal direction, and vertically alternates chroma channel on each line.
That's just 4:2:0 video. I'll leave the other subsamplings as homework for the viewer. Got the basic idea, moving on.
pixel formats
In audio, we always represent multiple channels in a PCM stream by interleaving the samples from each channel in order. Video uses both packed formats that interleave the color channels, as well as planar formats that keep the pixels from each channel together in separate planes stacked in order in the frame. There are at least 50 different formats in these two broad categories with possibly ten or fifteen in common use.
Each chroma subsampling and different bit-depth requires a different packing arrangement, and so a different pixel format. For a given unique subsampling, there are usually also several equivalent formats that consist of trivial channel order rearrangements or repackings due either to convenience once-upon-a-time on some particular piece of hardware or sometimes just good old-fashioned spite.
Pixels formats are described by a unique name or fourcc code. There are quite a few of these and there's no sense going over each one now. Google is your friend. Be aware that fourcc codes for raw video specify the pixel arrangement and chroma subsampling, but generally don't imply anything certain about chroma siting or color space. YV12 video to pick one, can use JPEG, MPEG-2 or DV chroma siting, and any one of several YUV colorspace definitions.
done!
That wraps up our not so quick and yet very incomplete tour of raw video. The good news is we can already get quite alot of real work done using that overview. In plenty of situations, a frame of video data is a frame of video data. The details matter, greatly, when it come time to write software, but for now I am satisfied that the esteemed viewer is broadly aware of the relevant issues.
Containers
So. We have audio data. We have video data. What remains is the more familiar non-signal data and straight up engineering that software developers are used to, and plenty of it.
Chunks of raw audio and video data have no externally visible structure, but they're often uniformly sized. We could just string them together in a rigid pre-determined ordering for streaming and storage, and some simple systems do approximately that. Compressed frames though aren't necessarily a predictable size, and we usually want some flexibility in using a range of different data types in streams. If we string random formless data together, we lose the boundaries that separate frames and don't necessarily know what data belongs to which streams. A stream needs some generalized structure to be generally useful.
In addition to our signal data, we also have our PCM and video parameters. There's probably plenty of other metadata we also want to deal with, like audio tags and video chapters and subtitles, all essential components of rich media. It makes sense to place this metadata, that is, data about the data, within the media itself.
Storing and structuring formless data and disparate metadata is the job of a container. Containers provide framing for the data blobs, interleave and identify multiple data streams, provide timing information, and store the metadata necessary to parse, navigate, manipulate and present the media. In general, any container can hold any kind of data. And data can be put into any container.
Credits
In the past thirty minutes, we've covered digital audio, video, some history, some math and a little engineering. We've barely scratched the surface, but it's time for a well earned break.
There's so much more to talk about, so I hope you'll join me again in our next episode. Until then--- Cheers!
Written by: Christopher (Monty) Montgomery and the Xiph.Org Community
Intro, title and credits music: "Boo Boo Coming", by Joel Forrester Performed by the Microscopic Septet Used by permission of Cuneiform Records. Original source track All Rights Reserved. www.cuneiformrecords.com
This Video Was Produced Entirely With Free and Open Source Software
GNU Linux Fedora Cinelerra The Gimp Audacity Postfish Gstreamer
CC BY-NC-SA A Co-Production of Xiph.Org and Red Hat Inc. (C) 2010, Some Rights Reserved
The making of…
Equipment
Camera
Canon HV40 HDV camera w/ wide-angle lens operating on a tripod.
The wide angle lens gives the camera a nice close macro mode, and approximately triples the amount of light coming into the sensor for a given zoom/aperture. Useful for shooting indoors at night.
No additional lighting kit was used.
Audio
Two Crown PCC160 boundary microphones placed on a table approximately 4-8 feet in front of the speaker, run through a cheap Behringer portable mixer and into the camera's microphone input.
No additional audio kit was used.
Sundries
Whiteboard markers by 'Bic'
Drawing aids by Staedtler, McMaster Carr, and 'Generic'.
Video shooting sequence
Scenes were pre-scripted and memorized, usually with lots of on-the-fly revision. (In the future... I'm totally getting a teleprompter. Wh000. OTOH, I can totally rattle off the entire video script from beginning to end as a party trick, thus ensuring I'll not be invited to many parties --Monty).
Diagrams were drawn by hand on a physical whiteboard with whiteboard markers and magnetic T-squares, triangles, and yardsticks. Despite looking alot like greenscreen work, there is no image compositing in use (actually-- there are two small composites where an error in a whiteboard diagram was corrected by subtracting part of the original image and then adding a corrected version of the diagram).
Camera operated in 24F shutter priority mode (Tv set to "24") with exposure and white balance both calibrated to the white board (or a white piece of paper) and locked. Microphone attenuation setting active, with gain locked such that room noise peaked at -40dB (all the rooms in the shooting sequences were noisy due to the building's ventilation system, or active equipment). Lighting in the whiteboard rooms tended to be odd, with little relative light cast on a presenter standing just in front of the whiteboard; a presenter is practically standing in the room's only shadow. Most of the room light is focused on the table and walls. Additional fill lighting kit would have been useful, but for the first vid, I didn't want 'perfect' to be the enemy of 'good'.
Autofocus used for whiteboard scenes, manual focus used for several workshop scenes as the autofocus tended to hunt continuously in very low light.
Continuous capture to a Thinkpad with firewire input via a simple gstreamer script.
Production sequence
All hail Cinelerra. You better hail, or Cinelerra will get pissy about it.
Most of the production sequence hinged on making Cinelerra happy; it is a hulking rusty cast iron WWI tank of a program that can seem like it's composed entirely of compressed bugs. That said, it was neither particularly crashy nor did it ever accidentally corrupt or lose work. It was also the only FOSS editor with a working 2D compositor. It got the job done once I found a workflow it would cope with (and fixed a number of bugs; these fixes are available from my cinelerra Git repo at http://git.xiph.org/?p=users/xiphmont/cinelerraCV.git;a=summary)
Choosing takes
Each shooting session yielded four to six hours of raw video. The first step was to load the raw video into the cinelerra timeline, label each complete take, compare and choose the take to use, then render the chosen take out to a raw clip as a YUV4MPEG raw video file and a WAV raw audio file. Be careful that Settings->Align Cursor On Frames is set, else the audio and video renders won't start on the same boundary.
Postprocessing
At this point, the raw video clips were adjusted for gamma, contrast and saturation in gstreamer and mplayer. In the earlier shoots the camera was underexposing due to pilot error, which required quite a bit of gamma and saturation inflation to 'correct' (there is no real correction as the low-end data is gone, but it's possible to make it look better). Later shoots used saner settings and the adjustments were mostly to keep different shooting sessions more uniform. The whiteboard tends not to look white because it's mildly reflective, and picked up the color of the cyan and orage audio baffles in the room like a big diffuse mirror.
The audio was both noisy (due to the building's ventilation system which either sounded like a low loud rumble or a jet-engine taking off) and reverberant (the rooms were glass on two sides and plaster on the other two). Early takes used no additional sound absorbing material in the rooms, and the Postfish filtering and deverb was used heavily. It gives the early audio in the vid a slightly odd, processed feel (I had almost decided the original audio was simply unusable). Later takes used some big fleece 'soft flats' in the room to absorb some additional reverb, and the later takes are less heavily filtered.
The postfish filtering chain used declip (for the occasional overrange oops), deverb (remove room reverberation), multicompand (noise gating), single compand (for volume levelling) and EQ (the Crown mics are nice, but are very midrange heavy).
Special Effects
Audio special effects were one-offs, mostly done using Sox. The processed demo sections of audio were then spliced back into the original audio takes using Audactity.
Video special effects (eg, removing a color channel, etc) were done by writing quick, one-off filters in C for y4oi. A few effects were done by dumping a take as a directory full of PNGs and then batch-processing the PNGs again using a one-off C program, then reassembling with mplayer. Video effects were then stitched back into the original video takes in Cinelerra.
Editing
All editing was done in Cinelerra. This primarily consisted of stitching the individual takes back together with crossfades. All input and rendering output were done with raw YUV4MPEG and WAV files. Note that making this work well and correctly required several patches to the YUV4MPEG handler and colorspace conversion code.
Encoding
Encoding was done by hand external to Cinelerra using mplayer for final postprocessing, the example_encoder included with the [Ptalarbvorm] Theora source distribution, and ivfenc for WebM.
Sample Theora encode command line (note this is using an mplayer patched for y4o support; it could be done just as easily with a yuv4mpeg pipe):
- 360p, 128-ish (a4) audio + 500-ish (v50) video
mplayer -vf hqdn3d,scale=640:360,gradfun=1.5,unsharp=l3x3:.1,yuv4ogg complete2.m2v -fast -noconsolecontrols -vo null > /dev/null & ~/MotherfishSVN/theora-ptalarbvorm/examples/encoder_example -a 4 -v 50 -k 240 complete2.wav output.y4o -o A_Digital_Media_Primer_For_Geeks-360p-a4+v50.ogv