Difference between revisions of "Ogg Index"
(→Ogg Index Track Format Version 1)
(→Ogg Index Track Specification Version 1)
|Line 2:||Line 2:|
'''DRAFT, last updated 24 September 2009'''
'''DRAFT, last updated 24 September 2009'''
Revision as of 22:04, 23 September 2009
Ogg Index Track Specification Version 1
DRAFT, last updated 24 September 2009
This specification is still a work in progress, and does not yet constitute an official Ogg track format.
Seeking in an Ogg file is typically implemented as a bisection search over the pages in the file. The Ogg physical bitstream is bisected and the next Ogg page's end-time is extracted. The bisection continues until it reaches an Ogg page with an end-time close enough to the seek target time. However in media containing streams which have key frames and interframes, such as Theora streams, your bisection search won't necessarily stop at a keyframe, thus you can't simply resume playback from that point. First you need to construct the keyframe's timestamp from the last page's granulepos, and seek again to the start of the keyframe and decode forward until you reach the frame at the seek target.
This is further complicated by the fact that packets often span multiple Ogg pages, and that Ogg pages from different streams can be interleaved between spanning packets.
The bisection method above works fine for seeking in local files, but for seeking in files served over the Internet via HTTP, each bisection or non sequential read can trigger a new HTTP request, which can have very high latency, making seeking very slow.
Seeking with an index
The Ogg index bitstream attempts to alleviate this problem, by providing an index of periodic keyframes in an Ogg file. The index is contained in a separate track which is embedded in the Ogg file, so that players which don't understand the index track can just ignore it. In streams without the concept of a keyframe, such as Vorbis streams where each sample is independent, the index can instead record the time position at periodic intervals, which achieves the same result. When this document refers to keyframes, it also refers to these independent periodic samples from keyframe-less streams.
The Ogg index bitstream provides seek algorithms with an ordered table of the Ogg page start-offsets and end-times of key points in the indexed streams in an Ogg segment.
A key point k is defined as follows. Each key point has an 8 byte offset o, an 8 byte time t, and a 4 byte checksum c. This specifies that in order to render the media at presentation time t milliseconds, the last page which lies before the start of all the packets containing all the key frames required to render at time t begins at offset o. The checksum c is the checksum of the page which begins at offset o, which enables you to verify that you're seeking to the intended page.
To seek in an Ogg bitstream which contains an index, you find the last key point in the index with time less than or equal to the target time. You then seek to the key point's offset, check that the page found there has checksum c, and then decode forward until you encounter the sample which corresponds to your seek target time. You are guaranteed to pass keyframes on all indexed streams with time less than or equal to your seek target time while decoding up to the seek target.
Be aware that you cannot assume that any or all Ogg files will contain an index, and so when implementing Ogg seeking, you must gracefully fall-back to a bisection search or other seek algorithm when the index is not present.
The index also only holds data for the segment in which it resides, i.e. if two Ogg files are concatenated together ("chained"), the index track in one Ogg segment does not contain information about the keyframes in the other Ogg segment.
The index also stores meta data about the segment in which it resides. It stores the start time and the end time, and also the length of the segment in bytes. This is so that if the seek target is outside of the indexed range, you can immediately move to the next/previous segment and either seek using that segment's index, or narrow the bisection window if that segment has no index.
Unless otherwise specified, all integers and fields in the bitstream are encoded with the least significant bit coming first in each byte. Integers and fields comprising of more than one byte are encoded least significant byte first (i.e. little endian byte order).
An Ogg index track starts with an identifier header packet which contains the following data, in the following order:
- The identifier "index\0".
- The index version format number, as a 1 byte unsigned integer. This specification describes version 1, so this field should have the value 0x01.
- The playback start time, in milliseconds, as an 8 byte unsigned integer, this is the presentation time of the first frame.
- The playback end time, in milliseconds, as an 8 byte unsigned integer, this is the end time of the last frame.
- The length of the indexed segment, in bytes, as an 8 byte unsigned integer.
- The number of key points in the index, 'n', as a 4 byte unsigned integer.
The track then contains one secondary header packet, which contains the actual index. This is the "index packet", and it must begin on a new page, but it may span multiple pages. The index packet contains the following:
- 'n' key points, each of which contain, in the following order:
- the page offset as an 8 byte unsigned integer, followed by
- the checksum of the page found at the offset, as a 4 byte field,followed by
- the presentation times in milliseconds of the key point, as an 8 byte unsigned integer.
The size of the data in the index packet is (n * (8 + 4 + 8)) bytes. The key points are stored in increasing order by offset.
The track then contains one empty EOS packet, which must start on a new page. The track therefore contains exactly three packets, on three or more pages.
The offsets stored in the keypoints is relative to the start of the Ogg bitstream segment. So if you have a physical Ogg bitstream made up of two chained Oggs, the offsets in the second Ogg segment's bitstream's index are relative to the beginning of the second Ogg in the chain, not the first. Also note that if a physical Ogg bitstream is made up of chained Oggs, the presence of an index in one segment does not imply that there will be an index in any other segment.
The exact number of keyframes used to construct key points in the index is up to the indexer, but to limit the index size, we recommend including at most one key point per every 64KB of data, or every 500ms.
There can be only one index track per Ogg bitstream segment. The index packet must occur before all non-metadata streams' content packets. In practice this means that the index packet will occur along with other secondary header pages, before the skeleton EOS page.
All pages in the index bitstream have their granulepos set as 0.
For a prototype indexer, see:
To see how indexes improves network seeking performance, you can download a development version of Firefox which can take advantage of indexes here:
Then point that browser here: