Videos/A Digital Media Primer For Geeks/making

From XiphWiki

Jump to: navigation, search

This page documents some of the background information behind the production of Digital Media Primer For Geeks. To see the video or its wiki-edition visit the main video page.

Contents

The making of…

Equipment

Camera

Canon HV40 HDV camera w/ wide-angle lens operating on a tripod. At the time I was looking for MyFirstVideoCamera, all six people [who did video work] recommended this same camera, and two said not to get it without the wide angle lens. I took their advice and have been happy with it. Among other nifty features, the camera offers true progressive scan modes, live firewire output, and the ability to act as a digitizer for external video input.

The wide angle lens gives the camera a nice close macro mode, and approximately triples the amount of light coming into the sensor for a given zoom/aperture. Useful for shooting indoors at night (eg, this entire video)

No additional lighting kit was used.

Audio

Two Crown PCC160 boundary microphones placed on a table approximately 4-8 feet in front of the speaker, run through a cheap Behringer portable mixer and into the camera's microphone input.

No additional audio kit was used.

Sundries

Whiteboard markers by 'Bic'

Drawing aids by Staedtler, McMaster Carr, and 'Generic'.

Video shooting sequence

Scenes were pre-scripted and memorized, usually with lots of on-the-fly revision. In the future... I'm getting a teleprompter. OTOH, I can totally rattle off the entire video script from beginning to end as a party trick, thus ensuring I'll not be invited to many parties.

Diagrams were drawn by hand on a physical whiteboard with whiteboard markers and magnetic T-squares, triangles, and yardsticks. Despite looking a lot like greenscreen work, there is no image compositing in use (actually-- there are two small composites where an error in a whiteboard diagram was corrected by subtracting part of the original image and then adding a corrected version of the diagram).

Camera operated in 24F shutter priority mode (Tv set to "24") with exposure and white balance both calibrated to the white board (or a white piece of paper) and locked. Microphone attenuation setting was active, with gain locked such that room noise peaked at -40dB (all the rooms in the shooting sequences were noisy due to the building's ventilation system, or active equipment). Lighting in the whiteboard rooms tended to be odd, with little relative light cast on a presenter standing just in front of the whiteboard; a presenter is practically standing in the room's only shadow. Most of the room light is focused on the table and walls. Additional fill lighting kit would have been useful, but for the first vid, I didn't want 'perfect' to be the enemy of 'good'.

Autofocus used for whiteboard scenes, manual focus used for several workshop scenes as the autofocus tended to hunt continuously in very low light.

Continuous capture to a Thinkpad with firewire input via a simple gstreamer script.

Production sequence

All hail Cinelerra. You better hail, or Cinelerra will get pissy about it.

Most of the production sequence hinged on making Cinelerra happy; it is a hulking rusty cast iron WWI tank of a program that can seem like it's composed entirely of compressed bugs. That said, it was neither particularly crashy nor did it ever accidentally corrupt or lose work. It was also the only FOSS editor with a working 2D compositor. It got the job done once I found a workflow it would cope with (and fixed a number of bugs; these fixes are available from my cinelerra Git repo at http://git.xiph.org/?p=users/xiphmont/cinelerraCV.git;a=summary)

Choosing takes

Each shooting session yielded four to six hours of raw video. The first step was to load the raw video into the cinelerra timeline, label each complete take, compare and choose the take to use, then render the chosen take out to a raw clip as a YUV4MPEG raw video file and a WAV raw audio file. Be careful that Settings->Align Cursor On Frames is set, else the audio and video renders won't start on the same boundary.

Postprocessing

At this point, the raw video clips were adjusted for gamma, contrast, and saturation in gstreamer and mplayer. In the earlier shoots the camera was underexposing due to pilot error, which required quite a bit of gamma and saturation inflation to 'correct' (there is no real correction as the low-end data is gone, but it's possible to make it look better). Later shoots used saner settings and the adjustments were mostly to keep different shooting sessions more uniform. The whiteboard tends not to look white because it's mildly reflective, and picked up the color of the cyan and orange audio baffles in the room like a big diffuse mirror.

The audio was both noisy (due to the building's ventilation system which either sounded like a low loud rumble or a jet-engine taking off) and reverberant (the rooms were glass on two sides and plaster on the other two). Early takes used no additional sound absorbing material in the rooms, and the Postfish filtering and deverb was used heavily. It gives the early audio in the vid a slightly odd, processed feel (I had almost decided the original audio was simply unusable). Later takes used some big fleece 'soft flats' in the room to absorb some additional reverb, and the later takes are less heavily filtered.

The postfish filtering chain used declip (for the occasional overrange oops), deverb (remove room reverberation), multicompand (noise gating), single compand (for volume levelling) and EQ (the Crown mics are nice, but are very midrange heavy).

Special Effects

Audio special effects were one-offs, mostly done using Sox. The processed demo sections of audio were then spliced back into the original audio takes using Audactity.

Video special effects (eg, removing a color channel, etc) were done by writing quick, one-off filters in C for y4oi. A few effects were done by dumping a take as a directory full of PNGs and then batch-processing the PNGs again using a one-off C program, then reassembling with mplayer. Video effects were then stitched back into the original video takes in Cinelerra.

Editing

All editing was done in Cinelerra. This primarily consisted of stitching the individual takes back together with crossfades. All input and rendering output were done with raw YUV4MPEG and WAV files. Note that making this work well and correctly required several patches to the YUV4MPEG handler and colorspace conversion code.

Encoding

Encoding was done by hand external to Cinelerra using mplayer for final postprocessing, the example_encoder included with the [Ptalarbvorm] Theora source distribution, and ivfenc for WebM.

Sample Theora encode command line (note this is using an mplayer patched for y4o support; it could be done just as easily with a yuv4mpeg pipe):

  1. 360p, 128-ish (a4) audio + 500-ish (v50) video

mplayer -vf hqdn3d,scale=640:360,gradfun=1.5,unsharp=l3x3:.1,yuv4ogg complete2.m2v -fast -noconsolecontrols -vo null > /dev/null & ~/MotherfishSVN/theora-ptalarbvorm/examples/encoder_example -a 4 -v 50 -k 240 complete2.wav output.y4o -o A_Digital_Media_Primer_For_Geeks-360p-a4+v50.ogv

Personal tools


Main Page

Xiph.Org Projects

Audio—

Video—

Text—

Container—

Streaming—